Please help us improve the quality of example sentences! Edit on Github

有二种基本的主流道拉料机构设计方法。There are two basic designs of sprue puller.

藉由我的测定设备，我检查溶碴和转轮。With my measuring equipment, I checked the sprue and runner.

Other words in sentence

边缘型或直入型水口都可以接受。Edge gate or sprue gate requiring secondary operation acceptable.

以下是与门面板和浇道演员仍然重视。Here is the cast faceplate with the gate and sprue still attached.

这在使用中心主流道拉料杆的时候尤为必要。This is particularly desirable when a central sprue puffier is used.

直浇道高度对流动性无显著影响。The influence of sprue height on the fluidity appears insignificantly.

热流系统的作用就是把材料送到模内的每一浇口。The function of the Heat flow system is to sent materials to sprue gate.

Other words in sentence

它们也可能被置于远远表面的模具，使之远离，从冒口或浇道。They may also be placed at far surface of a mold, away from a riser or sprue.

对喷嘴选择，直、横浇道及浇口设计等进行了分析。Make analyses of selecting nozzle and designing sprue runner and gate and etc.

对于小型熔模铸件，直浇道的截面形状将影响其工艺出品率。The sprue sections influence the technological yield of small castings in investment casting.

这个洞你看到的是为尾座浇道洞，滑轮的浇口是不可见图片。The hole you see is the sprue hole for the tailstock, the pulley's sprue is not visible in the picture.

我得检查一下它的唧嘴大小，顶棍孔位置以及顶杆螺牙类型是否正确。I need to double check the sprue radius, the location of the KO hole, and the thread type of ejector rod.

Other words in sentence

步进电机带动加注枪，实现偏心桶口的自动定位。Step motors drive sprue guns to realize the accurate positioning of the eccentric bunghole automatically.

为了避免这种不希望看到的现象，一个主流道拉料机构总应在设计中加以考虑。To avoid this undesirable feature, an arrangement for pulling the sprue should always be incorporated in the design.

常用的主流道拉料方法在主流道入口正对面的位置上直接设置一个带底切的顶杆或一个带底切的凹坑。The common sprue pulling methods unifies an undercut pin or an undercut recess situated directly opposite the sprue entry.

双分型面注射模，常用于一模多腔、点浇口形式浇注系统的注射模。The injection mold with double parting surfaces was usually used in the multi-cavity structure and pin sprue injection system.

浇注温度越高、直浇道空心面积率越大，铝液充型速度越快。The higher the pouring temperature or the larger the sprue hollow area rate is, the faster the filling velocity of molten aluminum is.

Other words in sentence

给出了直一内二单元浇注系统内浇口出流的实际作用压头和速度的计算公式，并对直浇道的正压充满程度进行了定量分析。The sprue keeps full or not and the fulling extent in pressure or non-pressure can be quantitatively calculated and practically controlled.

长期以来，由于没有有效的方法测量浇口杯内的铁水液位，浇注一般都是用人工控制。Because there are no effective methods to measure molten iron level in the sprue cup, at present most of pouring systems work in manual mode.

流入底切的塑料冻结后，提供了一个足够的粘滞力，在模具打开时可以拉出主流道。The plastics material which flows into the undercut, upon solidifying, provides sufficient adhesion to pull the sprue as the mould is opened.